Yes, this is possible. However, unless it was the AC compressor clutch and pulley which failed, bypassing the AC pulley is unnecessary. Simply disconnect the wire to the AC compressor clutch and that should do the trick.
Table of Contents
Is there a way to bypass the AC compressor?
The compressor cannot be bypassed without the use of a compressor bypass pulley. It would cost more for a bypass for the compressor than it would be to just replace the compressor pulley. Install a new pulley or pulley bearing if it can come off of the compressor and then put on a new belt.
How do I manually engage my AC compressor clutch?
How do you manually jump an AC clutch?
At the compressor’s front side, unplug the single wire connector, take a jumper wire and attach it to the wire that you just disconnected from the compressor. Connect the other end of the jumper’s wire to the positive terminal of the car battery. This will enable the compressor to start manually.
What happens when you bypass AC compressor?
Although your engine will run fine, it won’t produce as much power with the factory compressor as it will after you bypass the AC compressor with an aftermarket pulley. Simply put, the bypass pulley spins with far less rolling resistance than your factory AC compressor.
How does an AC bypass pulley work?
An AC bypass pulley is a free spinning pulley used to replace the AC compressor on an automotive engine. When the AC compressor goes bad in a vehicle, a consumer often will choose to install an AC bypass pulley. … Once installed the vehicle will no longer have air conditioning.
Can you drive with a locked up AC compressor?
Recommended Services. Your car is not safe to drive since the air compressor is operated by the same drive belt as the remainder of the engine (serpentine belt). Because the AC compressor has seized, this could cause the belt to lock up other components resulting in major engine damage.
Can you replace AC clutch without removing compressor?
Yes, you can technically replace the clutch without removing the compressor. The reason people suggest doing them together is that when one fails, the other usually isn’t too far behind it. It’s just a matter of convenience to replace them both since you’re already doing most of the same steps anyway.
Can you fix a locked up AC compressor?
If your compressor seizes or gets locked up, it can sometimes be mechanically freed to get your unit cooling again right away. Soon the compressor may fail again or sometimes it will chug along for a good while which buys you a little time to stop sweating and make a plan to replace it.
What should I do if AC compressor clutch is not engaging?
If the compressor clutch doesn’t engage; that usually means, there’s an electrical or mechanical problem with the compressor. If the AC is not blowing cool air into the car, you may want to do a visual inspection of the AC compressor clutch and determine if you can see what might be causing the clutch to not engage.
What causes AC clutch not to engage?
If the clutch doesn’t engage, the problem could be a blown fuse, an open in the wire to the clutch coil, a bad clutch coil, a poor ground, or a low pressure lockout. In some vehicles the compressor clutch relay is turned on and off by the low pressure switch and the evaporator temperature sensor.
What controls the AC compressor clutch?
Looking at the graph the compressor clutch has a unique relay, it has a compressor control relay that operates in a variety of ways depending upon the application. From the two fuses, one is controlling the coil in the relay (using a 10 amp fuse) that feeds from the relay.
How do I bypass the AC on my thermostat?
Can you turn a car AC compressor by hand?
Yes, you should usually be able to rotate a car’s air conditioner compressor clutch by hand. It won’t spin around at the daintiest touch of a finger—you may need to put a modest amount of effort into it—but it should be spinning.
How do you bypass an AC pressure switch?
Can AC compressor cause belt to break?
Hi there, yes, the air conditioning compressor is capable of breaking the serpentine belt a couple of ways. If the AC compressors seizes while operating, the shock load can snap the serpentine belt. If the AC clutch bearing seizes while the AC compressor is not operating, the belt can snap then as well.
How do you install a bypass pulley?
How do you open a stuck compressor?
Another trick which can be used on single-phase compressors is to reverse the start and run leads of the compressor and momentarily energize the compressor. This may also help to free the piston. Only do this for a few seconds and then switch both the run and start leads back to their original position.
What is idler pulley used for?
The idler pulley is a common part that’s found on the majority of the vehicles on the road. Its primary function is to provide tension and guide the engine drive belt. These belts wrap around the various parts of the engine such as the power steering pump, alternator, water pump etc…
How do you remove the pulley from an air compressor?
How do you remove an AC compressor from a car?
What causes AC compressor clutch to lock up?
Without professional maintenance, your car’s conditioning compressor can seize or lock up. Some of the causes for car air conditioning compressor locking up include incorrect or low quality refrigerant being used, low coolant levels, and improper lubrication.
Can you drive with a broken AC compressor clutch?
It’s not a good idea to drive with a broken A/C compressor. While you can sometimes drive your vehicle with a broken A/C compressor without needing expensive repairs, it’s not wise. When these integral parts of your car’s air conditioning system break, that can cause greater damage to your engine and even your health.
Should the AC clutch spin freely?
Most AC clutches are designed to spin freely when disengaged, and also with the pulley and compressor when those are engaged. If the clutch spins freely at all times, and the compressor never comes on, then it may not be engaging and therefore needs to be replaced.
How do I know if my AC clutch relay is bad?
Common signs include inconsistent cooling, not hearing a click from the compressor turning on, and no cold air.