Fuel injectors are numbered to correspond with the number assigned to the cylinder that they serve. The manufacturer determines the numbering of the cylinders.
How do I identify my BMW injectors?
The index number can be found on the head of the injector after the BMW part number. An example of this is 13538616079-11 where “11” is the index number. Injectors with index 10 and lower have a different calibration and construction than injectors with an index of 11 or higher.
How do I find my injector number?
The code is usually located on the injector head. DENSO Common Rail injectors – generally all require coding, although some very early versions may not. A typical code length is 16-24 alphanumeric characters depending on the vehicle make. The code is usually found on the injector connector.
How do you code BMW fuel injectors?
- Step 1: Replace the Injectors.
- Step 2: Plug the MX808 into the OBD2 Port.
- Step 3: Select “Service”
- Step 4: Select “Injector” from the service menu option list.
- Step 5: Select Vehicle Make.
- Step 6: Read the Vehicle VIN.
- Step 7: Verify Vehicle Information on the Next Table.
Are all BMW injectors the same?
The only difference between these injectors at the end of the day is the retail price. The TSB is specific for the S63 V8 which is the highest stock output engine that uses this particular type of direct fuel injection system. Remember that the BMW N54, N63, and S63 engine in ETK use the same fuel injector.
Do BMW injectors have to be coded?
It’s called calibrating the injectors and yea it mandatory. Each injector is different and it would be cheaper if you wrote down the 6 digits so the shop (whomever you choose) doesn’t have to pull the engine cover to get them. The code is based on the piezo crystals inside it.
How many digits are the injector ID code?
The code has 30 characters printed on top of the injector. If the correction code programmed in the engine DCU is incorrect for the injector, the engine may stall and run very badly at idle. The engine may also break down and have a reduced service life.
Is there a fuel injector code?
The most common fault codes associated with a clogged fuel injector are P0171 and P0174, which indicates the engine controller is seeing a lean condition. It is also possible to see fault codes for a rich condition if the injector is leaking or not atomizing correctly.
What happens if I don’t code my injectors?
Non start – In newer systems if you do not code in the injectors the vehicle will not start. Poor / lumpy running – as the injectors are not coded, the ECU will carry on fuelling as if the previous injector was still present, which can cause poor performance.
What are the 3 types of injectors?
Your vehicle can be equipped with one of the three most common injection systems on the market. GDI (Direct injection), SDI (Semi-direct injection) or TBI (Throttle body injection).
Do injectors need to be programmed?
Coding of a fuel injector – is a mandatory step in injector repairs. By coding the injector you make a correction, perfectly balancing hydralic parametres of the electromagnetic injector, as well as the piezoelectric injector in case of the Piezo Bosch.
Are all fuel injectors compatible?
If the body of your car’s injectors is gray, keep in mind: injectors of all releases ARE compatible! So, your car can have injectors with a different release for each cylinder!
Why do BMW injectors need coding?
They need to be coded so the ECU knows the flow rate at what voltage of the injector. If you are lucky, you could switch it out with an injector with a similar specs (-0.1 or +0.1) and you may not need to code them.
What do the numbers on fuel injectors mean?
Fuel Injectors are sized by their flow rate. Flow rate is a measurement of how much fuel can be delivered over time. It is listed in pounds per hour (lbs./hr.) or cubic centimeters per minute (cc/min.).
How much does BMW charge to replace injectors?
Generally, replacing fuel injectors can cost anywhere from $800 to $1500 depending on the repairs and labor costs. New fuel injector parts can cost anywhere between $600-$1200. To that, expect to pay about $200-$250 in labor charges.
What brand are BMW injectors?
The Bosch OE replacements are the same as the BMW injectors.
What type of fuel injection does BMW use?
Looking at the current BMW line-up, all gasoline engines available in the US are now turbocharged and direct injected. BMW made the switch to direct injection for good reason, however it also comes with some downsides.
Is it best to replace all fuel injectors at once?
Unless you need to fix other things that may be causing your fuel injector to fail (which is usually the case), replacing only one will do little good and cost time and money. If the car is old and you have the budget, replacing all of them can help you avoid future problems.
Should I reset ECU after changing injectors?
You dont need to punch in a code or anything, but it would not hurt to reset your ecu after installing the new injectors to clear any check engine codes.
Can you code BMW yourself?
If you want to try coding your BMW yourself, you only need a coding interface cable (ENET or DCAN depending on your vehicle) and a BMW coding tool.
Can I code my own BMW?
BimmerCode allows you to code your BMW or MINI yourself, customize it according to your wishes and unlock hidden features.
What can I use to code injectors?
Injector programming can be carried out with high level Diagnostic Scan Tools such as G-Scan or Autocom ICON. Care must be taken when reading the identification code stamped on the injector to ensure the correct number is entered into the ECU for the corresponding cylinder.
What is injector coding scan tool?
Injector coding scan tools can be used to read injector compensation codes, injector live data and programme new injector codes to the ECU for accurate communication and Injection control.
Will a leaking fuel injector throw a code?
Will A Bad Fuel Injector Throw A Code? The first step you should take to address your leaking fuel injector is to confirm that this is indeed your problem! Since a leaking fuel injector may throw a code or show up on a test, different devices can help you pinpoint the faulty injector.
Will injector cleaner fix a misfire?
Fortunately, you’re right about clogged fuel injectors being a symptom of a misfiring engine. If used correctly, though, a fuel injector cleaner should remedy the problem and stop your engine from misfiring.