Locate the small odometer button near the bottom left corner of the instrument panel. Press and hold it until the service message appears. Release the button, and press and hold it again until the message says “Reset?”.
Table of Contents
How do you reset the brake light on a 2015 BMW X3?
- Turn the ignition to the on position but do not start the engine.
- Open the driver’s side door and wait 30 seconds.
- Turn the ignition to the off position and wait another 30 seconds.
- Start the car.
How do you reset the brake light on a 2015 BMW?
Here’s How to Reset Your Brake Warning Light Insert the key (or key fob) in the ignition. Move the key to position 2, but don’t start the ignition. Open the driver’s door and wait for approximately 10 seconds. After completing the above three steps, the brake pad lights should reset!
How do you reset BMW brake wear indicator?
How do you reset the brake fluid light on a BMW X3?
How do you reset the brake light on a 2015 BMW x5?
Why is my BMW brake reset unsuccessful?
The warning means the sensor was tripped. Once tripped it must be replaced to do a reset. You also may need to clear the fault codes with an OBD diagnostic tool before a reset is possible. If you replace the sensor and try to reset and it still says “reset impossible” you’ll definitely need a scan tool.
How do you reset the brake light on a dashboard?
- Push the brake pedal a few times to ensure contact between the brake pads and discs.
- Switch the dashboard off for a few seconds.
- Turn the dashboard back on again and see if the light still remains. If the brake warning light is still illuminated, then seek assistance and advice.
Why does my BMW brake light stay on?
Bad Switch: One common reason for the Parking Brake light to stay on is a failing or failed switch. This can be checked easily by jiggling the handle after it is down. If the light turns off (or turns off and then back on), the switch is the most likely culprit and will need to be replaced.
How do you reset the brake warning light on a BMW 3 Series?
Push and hold the “BC” button of the turn signal stalk until it states “Reset?” let go of the button and push the button back in and hold, a little clock will come up, once the clock graphic besides the reset goes away let go. Turn the car off and resart as normal.
Why does my brake light stay on my dashboard?
Examine your parking brake and pull on the release mechanism to ensure that it is completely disengaged. If the dashboard light remains on, it’s telling you that thre is a brake system problem that could prevent you from stopping your vehicle.
Do you have to replace brake sensor BMW?
The brake pad sensor should be replaced every time you replace your brake pads! You don’t have to replace the sensor every time, but not doing so can result in you getting an inaccurate reading on the amount of life left on your pads, and result in the notification always appearing on your dash/iDrive system.
How do you reset the brake fluid on a 2015 BMW x1?
How do you reset the red exclamation mark on a BMW?
Press in the end of the stalk to select. Press and hold for about 5 seconds and a tick should appear then just drive off and it will reset on the move.
How do you reset the brake fluid on a 2016 BMW x5?
How do you reset the brake light on a 2016 BMW x1?
Hold the reset button or BC button on the end of the turn signal lever until you see a prompt asking you if you’d like to reset the warning. Press the reset or BC button until the display shows it is resetting and confirm reset if prompted.
How do you reset the rear brake light on a BMW x5?
What does brake system drive moderately mean?
It’s fine, just means that you’ve triggered the brake sensor in the pad. The idrive is just an estimate, this warning comes up when the pads physically trigger the sensor at a set wear level.
How do you reset the brake light on a BMW f30?
How do you reset the brake fluid on a BMW f30?
- Without pressing the brake/clutch, press the start/stop button.
- Wait for the service reminder to disappear.
- Press and hold the odometer reset button.
- At the value you want to reset, press and hold the odometer reset button.
- Press and hold odometer reset button again until value is reset.
How do you reset the brake sensor on a BMW x2?
How do you reset the maintenance light on a 2016 BMW X3?
How do you reset BMW faults?
What does yellow triangle with exclamation point mean on BMW?
That’s your traction control. If it’s lit, it means traction control has been deactivated. If it flashes, it means the traction control is active.
Why is my brake light on but brakes work fine?
Defective Sensors – Sensors located in the brake master cylinder measuring brake fluid or the parking brake sensor may fail, prompting the brake light to come on. An expert on brake repair should be able to identify the sensor that has caused the light to come on and replace it.