Locate the small odometer button near the bottom left corner of the instrument panel. Press and hold it until the service message appears. Release the button, and press and hold it again until the message says “Reset?”.
Table of Contents
How do you reset the brake light on a 2011 BMW?
Here’s How to Reset Your Brake Warning Light Insert the key (or key fob) in the ignition. Move the key to position 2, but don’t start the ignition. Open the driver’s door and wait for approximately 10 seconds. After completing the above three steps, the brake pad lights should reset!
How do I reset the brake pad lights in a BMW?
How do I turn off BMW brake notification?
Use the reset button or, depending on the model, the controls on the turn signal lever to scroll through the settings until you find the brake warnings. Hold the reset button or BC button on the end of the turn signal lever until you see a prompt to reset the warning.
Why is my BMW brake reset unsuccessful?
The warning means the sensor was tripped. Once tripped it must be replaced to do a reset. You also may need to clear the fault codes with an OBD diagnostic tool before a reset is possible. If you replace the sensor and try to reset and it still says “reset impossible” you’ll definitely need a scan tool.
How do I reset my 2011 BMW?
How do you reset the brake light on a dashboard?
- Push the brake pedal a few times to ensure contact between the brake pads and discs.
- Switch the dashboard off for a few seconds.
- Turn the dashboard back on again and see if the light still remains. If the brake warning light is still illuminated, then seek assistance and advice.
How do I reset my electronic brake system?
- Switch the ignition to the ON position and shift the gear lever in PARK.
- Pull and release the EPB button to activate the electric parking brake.
- Pull and hold the EPB button until you hear a mechanical sound, then release the button.
Why is my brake light still on after changing my brakes?
That light means your parking brake is on. If your parking brake is off, and the light stays on, it means you brake fluid is low. If your fluid is full and the light is still on… there may be a problem with the hydrulic system or booster.
How do I reset my electronic brake control module?
Step One: Disconnect the positive cable from your car battery. Then, hold down the brake pedal to drain the vehicle’s electrical system. This will result in a reset of the car’s central computer. Plug the cable back in to restore power.
How do I clear BMW service message?
- Turn on the vehicle’s electrical systems but do not start the engine.
- Press and hold the small odometer button near the bottom left corner of the instrument panel until the service message appears.
- Release the button, and press and hold it again until the message says “Reset?”.
How do I clear BMW control messages?
- Turn the ignition on.
- Dismiss or wait for all warning and failure messages to disappear.
- Use left stalk to navigate to “CHECK” submenu.
- Press BC button on the left stalk and hold it pressed for 5 seconds.
- Release the button when BMW CC-ID codes appear on the bottom display.
Is BMW brake pad sensor accurate?
If properly installed, it is very accurate as it is an item that gets detroyed when the minimum level is reached, and so it needs to be replaced. Unless your car shakes noticeably when you brake, you should not worry about it… You are doing the right thing by keeping an eye on them…
How do you reset ABS after brake job?
How do I reset my brake controller?
To reset the Pilot brake controller part # 80550 all you have to do is unplug the connector behind it for a few minutes. Doing that will return it back to the factory presets.
How do I get to BMW secret menu?
What does resetting a BMW computer do?
After your BMW is serviced the mechanic will reset the computer so it can register your mileage which is how you know when the vehicle needs service again in the future.
How do you reset the brake warning light on a BMW 3 Series?
Push and hold the “BC” button of the turn signal stalk until it states “Reset?” let go of the button and push the button back in and hold, a little clock will come up, once the clock graphic besides the reset goes away let go. Turn the car off and resart as normal.
Why does my brake light stay on my dashboard?
Examine your parking brake and pull on the release mechanism to ensure that it is completely disengaged. If the dashboard light remains on, it’s telling you that thre is a brake system problem that could prevent you from stopping your vehicle.
Will disconnecting battery reset ABS light?
Will Disconnecting The Battery Reset The ABS Light? Yes, if the car battery is disconnected long enough it will reset the ABS light.
What does EPB Reset mean?
EPB Reset Resets the cable if the Emergency release cable has been activated. EPB Un-jam Allows the EPB to be un-jammed when the vehicle has entered a state where the brakes screech when applying the Parking Brake, the rear brakes squeak or rub when the vehicle is moving or there is evidence of shoe-drag.
How do I reset my BMW parking brake?
Why does my brake light stay on even though my foot is off the brake pedal?
This is usually caused by corroded components or debris in the brake pedal assembly. If this issue persists and isn’t resolved quickly, you may also risk damage to your vehicle’s brake pads and rotor.
Why would ABS light come on after replacing brake pads?
Here are some of the issues that could cause your ABS and Traction Control light to come on after a brake job: Contaminated brake fluid. The wheel speed sensor was knocked loose during the service. The sensor connector wires were not reconnected to their original position.
What 2 reasons would cause your brake system warning light to come on?
When this light comes on, it means one of two things. Either the hydraulic fluid (brake fluid) in the master cylinder is low, or the parking brake is engaged. Your brakes are comprised of a network of brake lines, tubes filled with hydraulic oil.