How does the ECM control the fuel pump?


Sharing is Caring


The ECM monitors most of the sensors in the engine bay in order to manage your vehicle’s air-fuel mixture and regulate the emission control systems. The ECM regulates four main parts of your vehicle’s operating systems: air-fuel ratio, idle speed, variable valve timing, and ignition timing.

What does a BMW fuel pump control module do?

The electronic fuel pump control module (EKPS) controls the power to your BMW fuel pump. EKPS control unit is a different component from the fuel pump. The EKPS unit is usually located in the trunk, side panel or under the rear seat while the fuel pump is mounted on top of the fuel tank.

What module controls the fuel pump?

The Fuel Pump Driver Module controls the voltage delivered to a vehicle’s fuel pump. By controlling the voltage, the module maintains optimal fuel pressure and fuel delivery to the engine throughout its full operating range.

Does a fuel pump control module need to be programmed?

The fuel pump control module must be programmed with the proper calibration software. The module stores and utilizes this information however if it is not properly configured with the correct calibration software, the fuel pump control module will not control all of the vehicle features properly.

What is a EKPM?

The fuel pump control module, also called EKPM found on all BMW E9x cars can be controlled using MaxxECU.

How do you reset a fuel pump control module?

  1. Switch off the ignition.
  2. Switch to start position.
  3. Switch off the ignition.
  4. Switch on the ignition to re-enable the fuel pump.
  5. If vehicle does not start, repeat steps 1 through 4.

How do you test a fuel pump control module?

YouTube video

How much does it cost to replace a fuel pump control module?

How Much Does a Fuel Pump Driver Module Replacement Cost? The cost of an aftermarket fuel pump driver module replacement can range between $100 to $550 for parts alone. Several factors affect pricing, such as brand and warranty. Labor can cost you an additional $125 to $300, depending on the rates in your area.

What controls the fuel pump relay?

The fuel pump relay is usually controlled by the ignition or Powertrain Control Module, and when switched on, will provide current to the fuel pump so that it may function.

Do you need to program a new fuel pump?

Fuel pumps are usually coded to the immobiliser system of a vehicle. If you do a fuel pump replacement your vehicle might not start, the only way to code the fuel pump is usually with a pin code specifically for the vehicle and advanced diagnostic tools.

What does code P069E mean?

What Does the P069E Code Mean? Diagnostic trouble code (DTC) P069E stands for “Fuel Pump Control Module (FPCM) Requested MIL Illumination.” It indicates that the FPCM has identified an issue in the fuel system and is requesting the PCM turn on the check engine light.

How do you test FPCM?

Ignition ON, engine OFF, command the FPCM Fuel Pump ON with a scan tool. Verify the fuel pressure is between 345โ€“690 kPa (50โ€“100 psi) with the pump running. 3. Engine idling at the normal operating temperature, Verify the FPCM scan tool Fuel Rail Pressure Sensor parameter is between 296โ€“310 kPa (43โ€“45 psi).

How do I know if my BMW fuel pump is bad?

  1. High Engine Temperature.
  2. Stalling at High Temperatures.
  3. Decrease in Gas Mileage.
  4. Engine Sputtering.
  5. Surging.
  6. Noisy Pump.
  7. Lower Engine Power.
  8. Problems Starting.

How do you remove the backseat of a BMW e90?

YouTube video

Is there a fuse that controls the fuel pump?

Most fuel pumps will run a 15 (Blue), 20 (Yellow), or 25 (Clear) amp fuse. Using a fuse that’s too small will cause the fuse to blow again. This is a normal condition as the fuse isn’t rated for the higher amps of a fuel pump circuit.

What causes fuel pump to not kick on?

However, the most common cause is a faulty fuel pump relay. When the relay is faulty, it can cause the fuel pump not to receive power, which will prevent it from working. Other causes can include a clogged fuel filter, a failed fuel pump, or a faulty fuel pressure regulator.

How do I reset my fuel sensor?

Press and hold the “Trip/Odo” button and turn the car back on. While you’re holding the button, turn the key back to the “ON” position. Hold the button down for another 2 seconds after the car’s back on, then release.

What are the symptoms of a faulty fuel pump relay?

  • #1 โ€“ You Can’t Start Your Vehicle.
  • #2 โ€“ Check Engine Light.
  • #3 โ€“ Engine Stalling.
  • #4 โ€“ Rough Acceleration.
  • #5 โ€“ No Noise From the Fuel Pump.

Does fuel pump module assembly include fuel pump?

The fuel pump assembly in a vehicle is responsible for sending the required amount of fuel at the right pressure and time to the engine. The assembly consists of a few key parts such as the screen filter, fuel pump and fuel pressure regulator.

What are signs fuel pump is going bad?

A bad fuel pump may overheat and inadequately deliver gas to the engine, causing it to run hot and turn off while on the road. In this scenario, your vehicle may start back up after overheating and shutting down, only to do the same thing a half-hour later. This scenario is a common sign of a bad fuel pump.

How long does it take to replace a fuel pump module?

It takes about two to three hours to complete the job. Depending on your make and model of vehicle, it can be quite a challenge. If you’re not confident in changing it yourself, it’s best to take it to a mechanic. They will be able to do it quickly and safely.

How much does it cost to replace a fuel pump on a BMW?

A fuel pump replacement cost can be anywhere between $220-$1,062, depending on your vehicle and its age. The entire car repair will include a labor cost ($124-$260) and the cost of auto parts ($95-$854).

Can a fuel pump fail suddenly?

Fuel pump failures tend to be sudden and unpredictable, with few symptoms to warn the motorist that trouble is brewing. And the higher the mileage on the vehicle, the greater the risk of a fuel pump failure.

Where is the ECM module located?

YouTube video

Can I replace an ECM myself?

The answer to the question “Is it hard to replace an ECM?” is NO! The parts themselves aren’t inexpensive (as long as you’re buying them from us!), plus high quality aftermarket and OEM ECMs can be easily installed yourself.

Craving More Content?

Carolina's BMW