The Average Cost to Replace your Car’s Drive Belt Tensioner is Between $235 and $267, Depending on Whether You Go to the Mechanic or DIY. This price range is based on national averages for all vehicles and does not factor in taxes, fees, or your particular make and model.
How do you know when belt tensioner is bad?
Appearance: Cycle the tensioner (mounted on the engine) through the entire range of motion (from stop to stop) by applying torque to the arm with a wrench. The tensioner arm should move smoothly and freely. Solution: If you notice a binding, sticking or grinding tensioner arm, the tensioner should be replaced.
How do I adjust the tension on my drive belt?
What does a BMW belt tensioner do?
As drive belts are installed the belt tensioner is tightened to manufacturer’s specifications, placing the proper amount of tension on the belt. It is bolted to the front of the engine, and the flat side of the drive or serpentine belt rests tightly against the belt tensioner pulley.
Can I drive with a bad belt tensioner?
Driving with a bad belt tensioner is unsafe since the tensioner is meant to guarantee ample tension that powers accessories. Wear on the belt tensioner will eventually cause the belt to slip, generate loud noise, and also create an unsafe level of heat along the accessory pulleys.
What does a bad drive belt tensioner sound like?
The timing belt tensioner knocking noise is a common sign that drivers notice when their car timing belt tensioner goes bad. If the timing belt goes loose, it starts “knocking” between its connected parts and would keep hitting the timing belt cover.
How long does it take to replace a belt tensioner?
Automatic belt tensioners, standard in most cars now, make changing a serpentine belt a simple DIY repair. Follow the clear photos and step-by-step instructions and you’ll be done in 15 minutes.
What happens if you don’t replace belt tensioner?
Over time, the belt tensioner will lose its capacity to apply tension to the serpentine belt. Sometimes, the mechanism will weaken or seize up from repetitive use. Other times, the pulley itself can warp, crack, or throw a bearing. This often results in a noticeable squeaking noise from the front of the engine.
How long does it take to replace a tensioner pulley?
If you are doing the job at home, give yourself about four hours to change all the parts. You will need the following tools and parts: Replacement idler pulley. Tensioner pulley.
Can a belt tensioner be adjusted?
To adjust the timing belt tensioner, you’ll need to loosen the bolts securing the tensioner and adjust the belt to its proper alignment. All vehicles are different, so be sure to read your owner’s manual before proceeding with a tune up.
How do you check belt tension?
Can a loose serpentine belt cause rough idle?
So if you have searched for answers to the question, can a bad serpentine belt cause rough idle? The answer is yes.
Can a bad tensioner cause loss of power?
Typically a damaged belt tensioner will not impact vehicle performance. It would cause the serpentine or drive belt to wear prematurely or to squeak – but not cause the acceleration issue.
Why do belt tensioners fail?
As the damper wears, the tensioner arm can bounce away from the belt, causing excessive belt slippage. This will in turn induce excessive heat into the belt, which will lead to premature belt failure.
What happens when your tensioner pulley goes out?
If the timing belt is loose because of a bad tensioner, then the timing of the valves will be off. This means problems in the engine, which will then result in the check engine light illuminating on the dashboard.
How long can I drive with a bad tensioner pulley?
So, how long can you drive with a bad idler pulley? The safety recommendation is not to drive the car at all and take it to a mechanic immediately. You should be concerned if the vehicle makes squeaking or rattling noises. The car can still run for months or break after a few days.
Can belt tensioner cause misfire?
The belt may oscillate between too little tension and too much tension. The belt will slip and catch, causing noise and vibration. This can cause a change in crankshaft speed that can be severe enough to cause the engine management system to think that a misfire just occurred.
Can a bad tensioner cause engine vibration?
Grinding noises – Grinding and rumbling noises are another common sign of tensioner or idler pulley failure, usually due to failing bearings. Excessive tensioner movement – Worn-out coil springs can also cause drive belt tensioners to loosen their grip on the drive belt, resulting in excessive vibration and rattling.
Should I replace belt tensioner or just pulley?
If the pulley is damaged, replace the tensioner assembly not just the pulley. If an idler pulley is damaged, inspect the tensioner also because vibrations caused by a bad idler pulley may damage the tensioner.
Can a belt tensioner make noise?
Tensioner noise A squeaking or rattling noise coming from the tensioner indicates wear on the tensioner’s internal components and impending tensioner failure.
Is timing belt and drive belt the same?
The timing belt is responsible for making sure the engine’s crankshaft, pistons, and valves operating insync or in time. (Hence the term timing belt.) Accessory drive belts are used to drive all the accessories that run off the front of the engine.
Should you replace belt tensioner with serpentine belt?
Chances are, you’ll replace the serpentine belt at least once before you have to replace a tensioner. In most cases, you’ll replace the belt several times before the tensioner. But every time you replace the belt, you should check the tensioner. A bad tensioner could ruin a brand new belt.
Is the idler pulley and tensioner pulley the same?
The primary distinction between tensioners and idler pulleys is the presence of an adjustable bolt. Tensioners are positioned on the bolt through mounting. Idler pulleys are not mounted to an adjustable bolt. However, the differences between idler pulleys and tensioners also extend to purpose.
How much should a tension pulley cost?
You will pay anything between $125 and $380 for a full idler tensioner pulley replacement cost. The parts can cost as much as $225 and as little as $85. The labor cost should range between $45 and $150.
How do you remove a tensioner?
Use the extension/breaker bar on the grooved pulley tensioner arm, rotate the tensioner counter clockwise to remove the pin/bolt. Slowly allow the tensioner to rotate in a clockwise direction until the tensioner reaches the low stop. Remove the three bolts that attach the tensioner to the engine.