1 Answer: Dewan Jasim. It’s fine, just means that you’ve triggered the brake sensor in the pad. The idrive is just an estimate, this warning comes up when the pads physically trigger the sensor at a set wear level.23 Aug 2016.
Table of Contents
How do you reset the brake light on a BMW 530i?
How do you reset the brake light on a BMW 5 Series?
How do you reset BMW brake warning?
- Turn the ignition to the on position but do not start the engine.
- Open the driver’s side door and wait 30 seconds.
- Turn the ignition to the off position and wait another 30 seconds.
- Start the car.
How do you reset the brake light on a dashboard?
- Push the brake pedal a few times to ensure contact between the brake pads and discs.
- Switch the dashboard off for a few seconds.
- Turn the dashboard back on again and see if the light still remains. If the brake warning light is still illuminated, then seek assistance and advice.
Why is my BMW brake reset unsuccessful?
The warning means the sensor was tripped. Once tripped it must be replaced to do a reset. You also may need to clear the fault codes with an OBD diagnostic tool before a reset is possible. If you replace the sensor and try to reset and it still says “reset impossible” you’ll definitely need a scan tool.
Why is my BMW brake light on?
If the dashboard light remains on, it’s telling you that thre is a brake system problem that could prevent you from stopping your vehicle. Turn off the engine and arrange to have the vehicle transported to your trusted mechanic.
How do I reset my BMW 5 Series?
Do BMW brake sensors need to be replaced?
The brake pad sensor should be replaced every time you replace your brake pads! You don’t have to replace the sensor every time, but not doing so can result in you getting an inaccurate reading on the amount of life left on your pads, and result in the notification always appearing on your dash/iDrive system.
Why is my brake light still on after changing my brakes?
Defective Sensors – Sensors located in the brake master cylinder measuring brake fluid or the parking brake sensor may fail, prompting the brake light to come on. An expert on brake repair should be able to identify the sensor that has caused the light to come on and replace it.
Why wont my parking brake light go off?
If it remains lit after the parking brake is released or if it turns on and off intermittently while you’re driving, it means you need to add brake fluid. If you check the fluid, add as needed and the light still doesn’t turn off, you’ll need to have the brake system inspected.
Can I drive with brake pad warning light on?
If your brake warning light comes on but your brakes feel normal, and brake fluid levels are normal – you can continue driving to a repair centre.
How do I reset my electronic parking brake light?
- Switch the ignition to the ON position and shift the gear lever in PARK.
- Pull and release the EPB button to activate the electric parking brake.
- Pull and hold the EPB button until you hear a mechanical sound, then release the button.
What 2 reasons would cause your brake system warning light to come on?
- The Parking Brake is engaged.
- Brake Fluid is low or leaking.
- Worn brake pads.
- The ABS System has failed.
- Brake lights burned out.
- Faulty sensors.
How do I clear my ABS and traction control light?
How do you reset the brake light on a BMW f30?
How do I reset my f30 brake sensor?
How do you reset the brake light on a BMW 4 Series?
How long can you drive with brake light on?
The brake warning light comes on well before the pads are fully worn. So this gives you time to arrange Brake Pad replacement at your ease. On average – you still have up to 500 miles to get the new pads installed.
Why would the brake warning light come on when you press on the foot brake?
This light is to alert you to potential issues with either your ABS (Anti-Lock Braking System) or your normal service brake system. Additionally, you may see this light if the brake fluid levels are low for either the master cylinder reservoir or the ABS reservoir.
How do you unlock the hidden menu on a BMW?
How do you reset the service light on a 2016 BMW 5 Series?
How do you clear a BMW check?
What does drive control malfunction mean BMW?
It means a fault registered in the control module and need to have a computer diagnostic to see what causing the problem.
How do you check BMW brake pads?
- Listening to them: If you hear metal scraping in the wheels when the vehicle is moving, then the brake pads are starting to wear down.
- Feeling for any vibrations: When the brake pads are wearing down, you may feel a vibration when pressing down on the brake pedal.