DTA DSN3402N – 2 BMW Axle Nuts, Spindle Nuts Size M27x1.
Table of Contents
What size socket do I need to remove axle nut?
36mm is correct. Make sure it’s attached to a decent breaker bar; those things are on there pretty tight. I honestly don’t know what I’d do without my impact wrench. FOr the life of me, the axle nut would not budge with my breaker bar.
Can Am x3 axle nut size?
The front and the rear are the same, all 30 mm.
Is a 10mm axle the same as 3 8?
3/8″ is an imperial measurement, which is pretty much the equivalent to 10mm.
What size socket fits the spindle nut?
He stated that you will just need a 1-1/2 inch socket for the 1.42-1.44 inch nut. This is the same size socket needed for a standard spindle nut.
Can I remove axle nut without impact wrench?
Do you need a special socket for axle nut?
These types of vehicles commonly use a splined axle to be tightened into the wheel hub by the axle nut, requiring a specially-designed axle nut socket to remove the nut. Some axle nut socket designs resemble a common socket wrench.
Can you over torque an axle nut?
No. Over tightening won’t put more of a strain on the bearings in this sort of design. You should’ve torqued those nuts down quite a bit.
Can I reuse my spindle nut?
Whichever style is on your vehicle, make sure you buy a new nut after removing the old one. The old nut will not hold the proper torque a second time. Don’t even think about “re-deforming” the old nut in your bench vise—it won’t work. New axle nuts cost about $3 and ball joint nuts usually less than $1.
What size bolts are the axle?
Axle Bolts14mm or 3/8″ 14mm bolts are sold in pairs. 3/8″ bolts are sold in pairs.
How tight should axle bearing nut be?
For context, the tolerable end-play for truck wheel bearings is the same: 0.001 to 0.005 inches, also expressed as 1 to 5 mil or 0.025 to 0.127 mm. In other words, it’s perfectly acceptable to adjust wheel bearings so that they are just a little bit loose, but not too loose.
Is 3/8 or 10mm bigger?
10mm = just over 3/8 inch.
Is 10mm or 40 bigger?
Straight walled pistol cases headspace off the case mouth. The . 40 S&W is . 142″ shorter than the 10mm Auto on average for in spec ammo.
Which is bigger 8 mm or 10mm?
The 8mm is a smaller ring diameter, and the 10mm is a bigger ring diameter.
What size socket is my nut?
Look through the table’s decimal column and select the first decimal larger than your caliper reading. Select the corresponding fraction. The website Sizes has a table showing Imperial (American) socket sizes. If the fraction is listed, it’s the size of your nut and required socket.
What size is my axle spindle?
How do you break an axle nut for free?
What happens if your axle nut is loose?
Loose axle nuts can become a serious problem. When the axle nut is loose it allows the wheel bearing to shift back and forth which can cause damage and cause the wheel bearing to fail. When the axle nut is installed properly it is staked so it cannot come back off, though it could still become loose.
Can you use a normal drill to take off lug nuts?
No. Here’s why: Lug nuts can become stuck, or frozen. Lug nuts can become rusted.
What tools do I need to change my axle?
- Breaker bar.
- Dead-blow hammer.
- Drain pan.
- Jack and jack stands.
- Large hammer or mallet.
- Long-handled diagonal cutting pliers.
- Pry bar or CV axle puller.
- Ratchet and socket set.
Which way does a axle nut come off?
The threads are not unusual; turn counter-clockwise to loosen them. The trick is to get yourself a piece of cast iron pipe.
Is it better to over or under torque?
The Importance of Proper Torque Typically, an under torqued bolt will deform and be unable to provide as much clamping force as needed. An over torqued bolt will break.
How much torque does an axle nut need?
Generally, jam nuts less than 2-5/8″ should be torqued to 200-300 lbf-ft; nuts 2-5/8″ and over should be torqued to 250-400 lbf-ft. See chart for exact torque specification. The final step is to use a dial indicator to verify the end play or free movement of the tire and wheel assembly along the spindle axis.
What happens if you overtorque wheels?
When you over-torque the lug nut you could cause stress fractures and this makes it no longer certified for the load rating, there is a risk of the lugs breaking under normal conditions and your wheels will pass you in traffic, rare, but it does create a safety concern.
How tight is a spindle nut supposed to be?
The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.