Where is the fuse box on a 2011 BMW 328i?
Why is OBD not communicating?
In most cases, communication issues can be caused by various reasons including: ignition-key position, connector-voltage issues, incorrect communication protocol, hung ECM, missing or bad data, and OEM-updated ECM software that is unknown to the scan tool.
What does fuse OBD mean?
January 22, 2022 by Bryan Mark. The OBD2 – short for On-Board Diagnostic – is mechanical equipment found mostly in vehicles. Its primary purpose is to skim through the activities and vitals of said vehicles, thus determining the overall electric power and functionality.
Is there a fuse for the gauges?
The fuse may be labeled gauges, clusters, or something similar. This fuse should have power on both sides with the ignition in the on position. If the fuses are okay, check for power at the instrument cluster.
Where is the fuse for the dashboard for the gauges?
Use your owner’s manual to find out where the fuses for your dashboard are located. The instrument panel fuse box is usually located inside the vehicle, and usually on the driver’s side. There should be a diagram inside the fuse box (or in the owner’s manual) that shows you what each fuse powers.
How do you reset the idrive on a 2011 BMW 328i?
What are common problems with 2011 BMW 328i?
- Oil Leaks From Lower Engine Area.
- Blower Final Stage Fan Resistor May Fail.
- Outside Mirror May Fold Out to Far.
- Noise and/or Vibration Due to AC System Low on Refrigerant.
- Noise From Top of Front/Rear Doors When Windows Are Fully Up.
- Coolant Loss Due to Leak from Expansion Tank.
How do I know if my BMW fuse is blown?
Does engine need to be running for OBD?
The ignition switch of your car must be set to the “ON” position but it is not necessary to start the engine. Then, pair the OBD scanner to your phone using Bluetooth and open the scanner’s mobile app on your phone.
Does car need to be running to use OBD?
The answer to your question is NO, the car does not have to be running to use a basic scan tool. It, however, does have to be running to see live data and perform specific tests.
Why isn’t my OBD2 working?
Blown Fuse If you’ve plugged into your car’s diagnostic port and aren’t reading anything, you might think that your OBD-II brain has been fried, but don’t declare it dead yet. The most common reason for getting no OBD code is simply a blown fuse.
CAN OBD damage car?
It’s completely safe to leave an OBD2 scanner tool plugged in while driving. In fact, it’s important to have your car running while you diagnose an engine code to avoid damaging the scanning software.
What fuse turns off check engine light?
There is no fuse for the check engine light. If it’s not working (i.e. if it doesn’t light up as part of the ignition sequence), chances are it was deliberately deactivated to hide a major issue and dupe you, the buyer, out of more money.
Can a blown fuse cause a check engine light?
Yes a fuse that controls an emissions device can be blown and cause a check engine light.
Can a blown fuse cause instrument cluster not to work?
A blown fuse is one of two guaranteed causes for a non-working instrument cluster and only happens when none of the gauges work.
Why did the gauges on my dashboard stopped working?
It could be either a bad sensor or a problem with the gauge itself. But it could also happen that all the gauges stop functioning at the same. This could be caused by defective instrument clusters or a blown fuse and require instrument cluster repair.
How do I reset my instrument cluster?
Reset cluster lights by disconnecting the battery. You can also remove all bulbs from your instrument cluster and reconnect your battery or simply disconnect and reconnect a single bulb connection. Headlight fuses blow often. The instrument cluster fuse can be located under the hood.
Can a blown fuse cause the speedometer not to work?
Faulty Fuse/Bad Wiring: In very wet conditions, it is possible for exposed wires to get wet and short out, causing a fuse to blow. When the fuse for your speedometer stops working, it can cause the speedometer to drop to zero.
What controls the gauge cluster?
These gauges along with all of the warning lights and displays are built into a single instrument cluster module. A processor controls most of these gauges and uses input from a variety of systems to make decisions about what to display.
How do you reset the gauges?
Press and hold the “Trip/Odo” button and turn the car back on. While you’re holding the button, turn the key back to the “ON” position. Hold the button down for another 2 seconds after the car’s back on, then release.
How do I reset my BMW OBD?
What does BMW software reset do?
How do I reset my BMW ECU?
You can reset a BMW ECU by unplugging the negative battery cable for 10 to 15 minutes. This should be enough to reset the ECU in most BMW models. If this doesn’t work, you can also try jumpstarting your car to reset it. This will also help if the issue is a drained battery!
Are there any recalls on a 2011 BMW 328i?
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.