Which way do you turn a serpentine belt tensioner?

Spread the love

Using a breaker bar, rotate the tensioner arm counter clockwise to release tension from the belt. Maximum allowable torque is 130 Nm (96 lb ft) . Insert the supplied M10 bolt or 10mm x 80mm pin into the feature on the arm to hold the tensioner while removing the fan drive belt. Remove the fan drive belt.

How much does it cost to replace a serpentine belt on a BMW?

Typically, a serpentine belt replacement may cost around $100-$195. This includes both labor charges ($75-$120) and spare parts ($25-$75).

How do you put a serpentine belt on yourself?

Using the serp belt placement tool, route the new belt around the belt path. Rotate the tensioner again while you load the belt around it. Wrap the new belt around the crankshaft pulley, then around the grooved pulleys. Finish the job by sliding the belt onto a rounded, non-grooved roller.

How do you change a BMW fan belt?

What are the symptoms of a bad serpentine belt?

  • Cracking.
  • Abrasions.
  • Rib separation.
  • Uneven wear on ribs or belt.
  • Malformation or melting.

What happens if serpentine belt breaks while driving?

This can lead to a sudden lost of power assist for the steering system, leading to the steering wheel all-of-a-sudden becoming very hard to turn. A broken serpentine belt may stop the water pump from circulating coolant through the cooling system, causing the engine can overheat.

How do you know if a pulley is misaligned?

What causes Fanbelt noise?

Our research has shown two main causes of belt noise: The belt squeals because there is improper tension in the belt drive system. This is usually caused by a worn automatic tensioner, but other causes can include a contaminated belt (oil, belt dressing, etc.) or a belt that is too long or worn out.

Where is the serpentine belt diagram?

Some vehicles have the serpentine belt diagram located on a decal somewhere in the engine compartment. But if your car does not have a decal, you can easily look up the diagram in a repair manual or repair database. Another option is to take a photo of the old belt before removal.

Is it possible to put a serpentine belt on wrong?

In some instances it may be possible to install a serpentine belt the wrong way. If this happens, one or more pulleys will rotate in the WRONG direction, affecting the operation of the alternator, water pump, A/C compressor or power steering pump. This can cause major problems.

How long does it take to replace serpentine belt?

It usually takes approximately thirty minutes for a mechanic to replace a serpentine belt. With the right tools and equipment, an auto mechanic can complete the process within thirty minutes to an hour.

How do you put a serpentine belt on without a tensioner?

If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt. Tighten the bolts again as you apply tension.

When should a serpentine belt be changed on a BMW?

Your serpentine belt was made to last. Under ideal circumstances, your car’s serpentine belt should last 60,000–100,000 miles. It’s important to replace this belt as part of your vehicle’s scheduled maintenance (even if it looks okay) to avoid it breaking while you’re on the road.

How many belts does a BMW E46 have?

Project Photos. Figure 1 The BMW E46 models utilize 2 multi-rib engine drive belts.

What does a serpentine belt do?

What is a serpentine belt? A serpentine belt is one long rubber belt along your car’s engine that provides power to many vital components in your car like the alternator, power steering pump, air conditioning and sometimes the water pump, according to Firestone.

Does serpentine belt affect acceleration?

Can A Bad Serpentine Belt Cause Acceleration Problems? Yes, it could. Bad serpentine belts cause loss of power. Especially in situations where slippage occurs and the alternator supplies power to the ECM.

What noise does a bad serpentine belt make?

It can squeak, squeal, chirp and clunk, imitating a bad engine-driven accessory or engine bearing. These noises can fool even the most experienced mechanic and lead to an expensive misdiagnosis. Squeals and chirps are definitely the two most common serpentine belt noises and usually result from different problems.

How do I know if my idler pulley is bad?

  1. Chattering, Squealing, or Chirping Sound.
  2. Corroded Surface.
  3. Excessively Loose Idler Pulley.
  4. A Bad Idler Pulley May Spin Excessively.
  5. Slow to No Spin or Binding.

Can I run my engine without serpentine belt?

The short answer is yes, your car will start even if the serpentine belt is broken or missing. To get the car going, the battery sends power to your starter motor. The starter motor provides enough power to get your engine moving and the combustion process started.

Can a bad water pump cause serpentine belt to come off?

Does the serpentine belt affect the transmission?

A Broken Serpentine Belt Could Ruin the Transmission Almost as soon as your car’s serpentine belt breaks, the engine will begin to overheat. Without the belt running, the water pump won’t be able to adequately cool your engine. When the engine overheats, your transmission may be damaged.

How do you realign pulleys?

There are two ways to align pulleys: Traditional and laser. Traditional alignment methods are quick but often inaccurate. With these methods, mechanical tools such as straightedges, tape measures, wire, string, feeler gauges, spirit levels and calibrated cones are used.

What are the three types of pulley misalignment?

  • Vertical angle misalignment. When a pulley has an angular error stemming from the incorrect positioning of a machine, it’s said to have a vertical angle or twisted misalignment.
  • Horizontal angle misalignment.
  • Parallel misalignment.

What can be caused by misalignment of drive pulleys?

Both misalignment conditions can create belt tracking problems, excessive wear, a chirping noise, and belt stability problems. Just a few degrees of misalignment can increase belt operating temperatures by 30° F, reducing belt life by as much as 50 percent.

Can I spray wd40 on serpentine belt?

Do NOT follow this link or you will be banned from the site!